We recently implemented the Configuration Manager 2012 Management Pack with Operations Manager 2012 to improve our ability to analyse load, performance and health of our environment.

Following the installation we initially had some issues with only the Primary Site being partially monitored and no site system roles being reported as healthy. This also included components such as our Distribution Points and Management Point.

Eventually we were successful and the Management Pack is now monitoring our environment in full. We did the following in order to resolve the problem.

  1. Installed the SCOM agent on all of our servers running either Site System or Site Server Config Manager components
  2. Enabled Agent Proxy under the Security Tab on each managed server with Config Manager infrastructure running on it including the Primary. This is contrary to the Management Pack documentation.
  3. Created SCOM exclusions for our Anti-Virus (Initially we had to completely uninstall it on our SCOM server for the monitoring to fully work)
  4. Disabled the client discovery object as we are not running Config Manager clients on our infrastructure
  5. Decreased the Hierarchy Discovery time from 86400 seconds to 600 seconds
  6. Decreased the Central Site Discovery time from 14400 seconds to 600 seconds
  7. Increased the Site Services Discovery, Hierarchy Discovery and Distribution Point Drive Discovery timeout from 300 seconds to 500 seconds
  8. Performed a manual Site System Discovery and Hierarchy Discovery from the SCOM console
  9. Waited approx 6 hours for monitoring data to initially full populate

2014-07-01_102127

Out of the box the management pack provides monitors for all the Config Manager infrastructure which you don’t need to create overrides for. However if you want to start collecting performance data then you do need to create overrides for each specific area. You can refer to the MP documentation here for the full list.

http://www.microsoft.com/en-us/download/details.aspx?id=29267

2014-07-01_102907

I’ve created some custom dashboards in addition to inbuilt ones (Note these wont work until you have tuned the MP to your requirements by enabling additional rules). Hopefully these give you an idea of what is possible with the MP. We have a couple of these cycling through on a large LCD panel in our office which give the Service Desk staff a good overview of the status of the Config Manager environment.

OVERALL HEALTH DASHBOARD

2014-07-01_103430

DISTRIBUTION POINTS PROCESSOR UTILIZATION

2014-07-01_104138

DISTRIBUTION POINTS FREE DISK SPACE %

2014-07-01_114029

MANAGEMENT POINT UTILIZATION – TOTAL ONLINE CLIENTS

2014-07-01_104313

MANAGEMENT POINT UTILIZATION – Authentication Requests / Sec, Hardware & Software Inventory Requested / Sec

2014-07-01_104956

HIERARCHY DIAGRAM SHOWING HEALTH ROLLUP

2014-07-01_105913

I’ve only really scratched the surface with what you can monitor and report on. Hopefully this gives everyone a good idea of what’s possible and how to do some basic installation troubleshooting based on what we experienced.

Cheers

Damon

Advertisements
Comments
  1. James Mooney says:

    Thanks helped a lot

  2. pmerigot says:

    Hi,

    I know it’s an old thread .. but I would like to know if with SCOM and this SCCM MP, it’s possible to monitor software update deployments ?

    • Damon Johns says:

      You can monitor the health of your software update points using the MP but not the actual compliance of your workstations against updates. For that you could you use either the built in reports or you could enable alerts on your software update group deployments so Operations Manager receives them. You would then need to tune Operations Manager to deal with the alerts in way that suits your environment.

      Cheers
      Damon

  3. Marlon says:

    Thank you for the very informative step by step. 🙂

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s